Search found 370 matches

by smoker77
Thu May 27, 2021 2:46 pm
Forum: FAQ
Topic: Starter Set Super-MP-3D can't track hedgehog
Replies: 1
Views: 313

Re: Starter Set Super-MP-3D can't track hedgehog

Hello Chris, From the map file I see you are using IA architecture with one submap with 4 stationary beacons. But the problem is that two of these beacons (17 and 45) have same ultrasonic frequency (31 kHz). This is not allowed in IA and dashboard should show notification about this on the top side....
by smoker77
Tue May 11, 2021 9:52 pm
Forum: FAQ
Topic: Pixhawk+Marvelmind with paired beacons intergration
Replies: 3
Views: 1023

Re: Pixhawk+Marvelmind with paired beacons intergration

Hello. In current version compass emulation (via SCL and SDA pins) works only for paired Super-Beacons and only with U-Blox protocol enabled. If you use HW4.9 beacons and NMEA, compass emulation will not work. To get heading data in NMEA you can purchase this license: https://marvelmind.com/product/...
by smoker77
Wed Apr 14, 2021 10:43 pm
Forum: FAQ
Topic: Ultrasonic calibration
Replies: 2
Views: 1274

Re: Ultrasonic calibration

Hello, 1. Yes, your assumption about less loud RX5 is correct in case of HW4.9 beacons. Super-Beacon's emitting sensors are equally loud. I think you are using HW4.9 beacons, yes? 2. Your signals look pretty weak for so small distance. Did you enable all sensors RX1...RX5 for transmitter and receive...
by smoker77
Wed Apr 14, 2021 10:07 pm
Forum: FAQ
Topic: Non accurate positioning - Fail to overlapping orange dots (hedgehog view from sumaps)
Replies: 1
Views: 970

Re: Non accurate positioning - Fail to overlapping orange dots (hedgehog view from sumaps)

Hello, 1. As you are using submaps with equal ultrasonic frequencies (31 kHz and 45 kHz beacons in both submaps), you should adjust TDMA sequence as described in section 9.2 of the operating manual (set TDMA sequence length to 2 for all stationary beacons, and set TDMA position in sequence to 0 for ...
by smoker77
Wed Apr 14, 2021 9:16 pm
Forum: FAQ
Topic: Setup Movement Path Closes Instantly
Replies: 3
Views: 2193

Re: Setup Movement Path Closes Instantly

Hello,

This is known issue, we will fix it in next software update.
Current workaround is to manually enable robot control setting for the mobile beacon as shown in the attached screenshot.
by smoker77
Wed Apr 14, 2021 9:09 pm
Forum: FAQ
Topic: Frequency Filter Selection
Replies: 1
Views: 903

Re: Frequency Filter Selection

Hello, Filter setting is not used for tracking in latest version of software (6.240), this setting is now only used for view signal in oscilloscope. Now system automatically selects the filter according to ultrasonic frequency of the emitting beacon. Note that if you use NIA and have beacons with di...
by smoker77
Wed Apr 14, 2021 8:46 pm
Forum: FAQ
Topic: Please advices of regarding the Marvelmind_Starer Set_HW_V4_9
Replies: 2
Views: 1138

Re: Please advices of regarding the Marvelmind_Starer Set_HW_V4_9

Hello, Unfortunately the file was not attached. If the forum engine rejects the file, please upload the file to some file hosting and place here the link to it. The best way after uploading the firmware to all beacons and modem is following: 1. Connect every beacon and modem to dashboard via USB and...
by smoker77
Wed Apr 14, 2021 8:24 pm
Forum: FAQ
Topic: Hedgehog disappears after creating service zones
Replies: 1
Views: 903

Re: Hedgehog disappears after creating service zones

Hello, Please give us some more information. What system do you use - IA or NIA? Can you share screenshot of the dashboard when mobile beacon is tracking and when it stops tracking after adding service zones? Also please send us a file generated by 'Save map' button in dashboard. Note that after add...
by smoker77
Wed Apr 14, 2021 8:11 pm
Forum: FAQ
Topic: how to change the map scale on my floorplan?
Replies: 1
Views: 877

Re: how to change the map scale on my floorplan?

Hello, You can simply drag and drop stationary beacons on the points over floorplan where these beacons are really placed. Last two dropped beacons determine the attachment of the beacons to the floorplan and the floorplan will be scaled accordingly. Please see also the video: https://www.youtube.co...
by smoker77
Wed Apr 14, 2021 8:05 pm
Forum: FAQ
Topic: NIA IMU issues.
Replies: 2
Views: 1014

Re: NIA IMU issues.

Hello, In current version of software for Super-Beacons IMU fusion position, speed and acceleration are still not available. It was working for HW4.9 beacons, but this functionality is not yet implemented for newer beacons, we are working on it. Currently you can get raw acceleration and gyro data f...